Quick answer: You can hang straight curtain panels across an arched window without following the curve. Mount a straight rod above the arch when a sound wall or ceiling surface allows it and you need the entire opening covered. Mount below the arch when you want to leave the curved glass visible and only need the rectangular lower section covered. If a sloped ceiling meets the arch, check usable wall area and bracket clearance before ordering; there is no universal mounting height that solves every arch.
The difficult question is usually not “what curtain goes with an arch?” It is “where can the hardware actually attach, and what must the fabric cover?” Answer those two questions first. The rest—panel length, width and header—follows from the chosen mounting point.
Start with the coverage you need
| Placement | What stays visible | Best fit when | Check before ordering |
|---|---|---|---|
| Straight rod above the arch | The arch appears when curtains are open; panels can cover it when closed | Full-window privacy or light control matters | Flat, structurally suitable wall or ceiling space; bracket and finial clearance |
| Straight rod below the arch | Curved glass stays visible at all times | You want the architectural shape on show and only need lower-window privacy | Mounting surface at the spring line; whether exposed upper glass is acceptable |
| Wall or ceiling track elsewhere | Depends on track line | The arch area has no usable wall above it | Manufacturer-approved track mounting, ceiling angle and support conditions |
Below-arch curtains do not provide privacy through the uncovered arch. If that upper glass faces a neighbor or lets unwanted light into a bedroom, decide how to treat it before choosing the lower rod position. A separate shaped shade or other solution may be needed; verify fit and mounting with its supplier rather than assuming a standard rectangular shade will follow the curve.

What if a sloped ceiling leaves no space above the arch?
Do not force a rod into the narrow wedge between the arch and the ceiling. First look for a level band of solid wall where brackets can sit below the curve. A straight rod there can dress the lower window while leaving the arch exposed. If you need to cover the whole arch, assess whether the adjacent wall or a ceiling-approved track offers a stable mounting line. A sloped ceiling can also rule out a standard ceiling bracket; ask about the actual angle, substrate and clearances before selecting hardware.
Curtarra's John Custom Curtain Rods page lists wall, ceiling and inside installation options, but it does not guarantee that any one option fits every angled ceiling or curved frame. The rod is straight, not shaped to follow an arch. For an unusual opening, send the installer or Curtarra a front-on photo, a side view of the ceiling slope and your proposed mounting line.
Illustration note: The featured image shows an above-arch rod where flat wall space is available. It is a visual concept, not a construction drawing or a documented Curtarra installation.

Measure the window and the mounting line separately
- Record the arch geometry. Measure the lower rectangular window width and height, plus the arch's highest point and the point where the curve begins.
- Mark the intended rod or track line. Measure its usable width and the distance to the ceiling, trim and any nearby wall return. Check whether brackets and finials have space.
- Decide where panels should finish. Measure from the installed hardware position to the chosen drop, such as the sill or floor. Do not use the arch's peak as the starting point if the rod sits below it.
- Allow room for open panels. Note the wall space on both sides and any obstruction, including furniture, doors or a sloped wall.
Take measurements at the actual installation line. The curtain hanging guide by window type covers general rod positioning; this article focuses on the arch-specific coverage and clearance decision. Curtarra's custom curtains for unusual windows page can help you plan made-to-measure panels after the hardware position is settled.
Choose the look after the practical decision
With an above-arch rod, open panels frame the full opening and closed panels can cover the curved top. With a below-arch rod, the arch becomes a permanent feature of the room. Either can look intentional. The better choice depends on the view, nighttime privacy, light and the available mounting surface—not a fixed “hang it high” rule.
If you plan to order custom panels, confirm the mounting choice and final dimensions first. For a sloped-ceiling arch, share photographs and measurements with the hardware seller or installer before placing a custom rod order.
Arched window curtain FAQ
Should a curtain rod go above or below an arched window?
Place it above the arch if the mounting surface allows it and you want the whole opening covered when curtains close. Place it below the arch if you want the curved glass permanently visible and lower-window coverage is enough.
Can I use a straight rod on an arched window?
Yes. A straight rod can cross above the arch or below the curved top. It will not follow the curve, so choose its height according to the coverage you need.
What if a sloped ceiling touches the top of the arch?
Look for a safe below-arch wall mounting line first. If full coverage is required, have an installer assess other wall or ceiling-approved hardware locations and the actual substrate and angle.
Will curtains below the arch give full privacy?
No. The arched glass remains uncovered. Check sightlines and light before choosing a below-arch rod; another treatment may be needed for the upper section.
Where do I start measuring curtain length?
Measure from the actual installed rod or track position to your desired lower edge. Do not start from the arch peak unless the hardware will be installed there.
